La spécification de couple gravée au laser (18 po-lb) élimine les approximations et garantit une cohérence absolue à chaque installation.
// TECHNICAL SPECIFICATIONS
SPÉCIFICATIONS DU PRODUIT
Diamètre du tube de la lunette
30MM / 34MM (Select Variant)
Type de rail
Picatinny Rail (MIL-STD-1913)
Type de montage
One-piece construction
Précision du retour à zéro
0.01
Concentricité
≤0.01MM/M
Chant MOA
0
Résistance aux chocs
≥1000G
Méthode de verrouillage
Two-screw locking
Matière principale
6061-T6
Finition de surface
Hard Anodized Finish
Processus de fabrication
CNC One-piece Machined
Poids
// WHY DISCOVERYOPT
Conçu pour la précision
Rodage interne au niveau du micron
Les tolérances d’usinage ordinaires créent des points de contrainte qui peuvent écraser les tubes de lunette ou provoquer un déplacement interne du réticule sous l’effet du couple.
- Contact à 100 % de la surface, répartition uniforme de la pression.
- Aucun dommage aux tubes - aucune cale requise.
// TECHNOLOGY
Conçu avec précision
Finition anodisée dure de type III avec une surface ultra-mate pour une résistance supérieure aux rayures et à la corrosion.
Finition anodisée conforme aux normes militaires
Contact à 100 % de la surface pour une pression uniformément répartie.
Rodage interne au micron près
Veillez à ce que l'erreur de coaxialité entre les deux axes internes soit presque nulle. Veillez à ce qu'il n'y ait aucune erreur axiale lors du montage de la lunette afin d'obtenir une plus grande précision.
Garantie de précision
📏 FITMENT GUIDE
Mount Fitment Assistant
×Recommended Center Height:
SHOP NOW
Note: Data is for reference only. Actual clearance may vary based on specific rifle setup.
// COMMON QUESTIONS
Des questions ?
Nous avons rassemblé les questions les plus fréquentes de nos clients. Si vous avez besoin d'autre chose, notre équipe d'assistance est toujours là pour vous aider.
Nous offrons une garantie à vie avec couverture complète pour certains produits. Si votre produit se casse ou ne fonctionne pas correctement, nous le réparerons ou le remplacerons gratuitement.
Aucune inscription ni aucun reçu n’est requis. Votre produit Discoveryopt est automatiquement couvert.
Non, les accessoires sont exclus. Cependant, vous pouvez les retourner gratuitement dans les 30 jours suivant l’achat.
Perte, vol, dommages intentionnels et dommages esthétiques qui n’affectent pas les performances.
Réparation ou remplacement gratuit si le produit tombe en panne ou fonctionne mal. S’il ne peut pas être réparé, nous le remplacerons par un produit neuf offrant des performances équivalentes ou supérieures.
Contactez simplement notre équipe d’assistance par e-mail. Aucun reçu n’est requis.
Dans la plupart des cas, les clients paient les frais d’expédition vers notre centre de service, et Discoveryopt prend en charge les frais de retour du produit réparé ou remplacé.
Les délais de traitement peuvent varier, mais nous nous efforçons de traiter toutes les demandes de garantie aussi rapidement que possible.
Vous pouvez soit trouver « Chat » dans le coin inférieur gauche du site Web pour communiquer directement avec nous, soit nous envoyer un e-mail à 📧support@discoveryopt.com.
Notre objectif est de vous garantir un produit qui répond à vos besoins. Si vous n’êtes pas satisfait, nous travaillerons avec vous jusqu’à ce que le problème soit résolu.
Vous ne trouvez pas ce que vous cherchez ? Notre équipe d’assistance technique est prête à vous aider.
Contacter l’assistanceCustomers praised this cantilever scope mount for "incredible build quality for the price" and excellent machining. The mount features marked torque specs, lightweight aluminum construction, and solid three-screw rail attachment. Most found it "perfect" for AR-15 setups with proper eye relief. A few noted manufacturing flaws like missing threads or scratches, and one suggested it's better suited for lower-recoil firearms.
A
34MM-1.5IN
Solid mount and perfect for bringing the scope to my comfortable eye relief position
W
34MM-1.93IN
Il supporto per ottica l'ho installato su un Ruger ar15 in 2 e 23 canna da 20 pollici si comporta egregiamente mi ha dato la possibilità di montare una sovra slitta all'ottica per un eventuale Red Hot
S
30MM-1.5IN
Scope Mount at an attractive price. Although this is not 7075 Aluminium, it is very high quality at a very low price. I would use this for anything but very hard hitting calibers and I plan on mounting it on my 6.5x55 SE Mauser 98 rifle when it comes back from maintenance.
A
34MM-1.93IN
Las monturas están muy bien ligeras y buen precio, pero podían traer unos adaptadores para poner visores de varios diámetros no solo de 34mm
J
30MM-1.93IN
Kiinnitys saisi olla tukevampi jos rymyää
C
30MM-1.5IN
Polecam
P
34MM-1.5IN
Very well made and fine finished mount. Reliable. Fast delivery
P
34MM-1.5IN
Great Product, very good Price. I use it on an 10/22 Ruger and Love it.
A
34MM-1.5IN
Bon support , tout la visserieest fourniavec qui est de bonne facture.
W
34MM-1.5IN
Ottimo accessorio ben realizzato e ben fatto Purtroppo per me mi è un po' basso Infatti ordinato l'altro più alto questo lo tengo di scorta per eventuali tipologie diverse, attualmente non l'ho utilizzato su nessuna delle mie armi perché appunto è troppo basso Però alla fineattualmente non l'ho utilizzato su nessuna delle mie armi perché appunto è troppo basso Però alla fine adesso avendone acquistato un'altra l'ho tenuto e su quest'ultima ci sta e calza a pennello
E
And held my LPVO well. It’s well made with good fit and finish. Additionally, it’s extremely lightweight. One nitpick is the fact that the overspray from the letters are noticeable. They definitely used stencils and HOPED the paint wouldn’t get anywhere else.Other than that, it’s a good mount.
m
They installed easy to the rail no problems there, All the dimensions seem correct as I didn’t have a single issue. comes with all the hardware to install but honestly a regular Allen wrench isn’t gonna do it you’re gonna need a special one that tell you how many ft lbs you’re putting on the scope during installation, well that is if you don’t want to risk over tightening and damaging your scope. If you know what you’re doing it’s got everything you need. The value for money is great here. Fit and finishes awesome and they look a lot more expensive than they are. And they look great. I put these on an AR 15 and a strike eagle scope, And I shot about identical, as the rings that came with the scope. These are bad ass.
R
This mount is well made and quite lightweight. The mount design is allows for quick attachment and detachment. The mount comes with extra screws and the machined parts are clean and accurate. This mount provides a more secure option for your scope than standard individual scope rings for about the same price as quality pair. Be sure to measure your scope so that you know it will fit properly with the set distance of the mounting points as one of my cheaper scopes, which I intended to use this mount with, has too short of a distance to use it...what a bummer but it's my fault. Through the pictures you can get a basic idea of the quality. The mount uses torx fasteners making them easy to safely tighten. If this mount fits your scope and guns mounting parameters you cannot go wrong with the purchase at such a low price entry point.
C
DISCOVERYOPT Rigid Precision Scope Mount,0 MOA Scope Mount, 30mm Cantilever Mount, 1.5inch Scope Mount, Picatinny Scope Mount Lightweight Rifle Scope Mount.This mount is a great combination of light-weight engineering and solid strength.I am using it to mount an LPVO scope on a .223 rifle, that I need positioned more forward for eye relief. I like the alignment lugs in the rings, and the heavy duty bolts.I am not a fan of all the torque values and tightening sequences printed in white on the black matte finish. Or the ring size and hight specs printed on the mount. Put that in the instructions. (well, there are not any..) That info is not needed after the mount is installed, and to me, it looks cheesy and amateur-ish. But, a minor complaint.Back to the heavy duty bolts: There are two extra bolts included in the box. And, all the bolts in the mounting base and in the rings are the same bolts using the same Torx wrench. This is good, because I needed a new bolt..When first loosening the bolts to install my LPVO scope, one of the three mounting base bolts was frozen, and very difficult to unscrew or loosen. When I finally got it about halfway out, I could see that the bolt threads were damaged. So, someone in the factory assembly had selected a damaged bolt and then proceeded to crank that thing forcefully into the mount. It damaged the aluminum threads in the base, but since the thread damage was in the middle of the bolt, half of the treads in the base hole were still undamaged. I used one of the extra replacement bolts to carefully "re-cut" the hole threads. It now threads in and out normally and holds securely. But, a disappointing discovery to make. I am glad it was fixable.This is otherwise a very well made mount.
D
It's not a LaRue or spuhr but then again it's not 4 or 5 hundred either. For the price the quality is phenomenal. When it comes to firearms parts, increase in quality and increase in price are not parallel. You start paying a lot more for little increments of increased quality. There hold zero and didn't require any lapping. For 99% of the population there are beyond what anyone will subject them to. Now if I was being deployed to a warzone where my life was on the line, then I might have my reservations and not chance it with these. Who knows they might be nearly as good. Anyway enough rambling. These are excellent.
O
I like the look and the weight of the mount! The frame seems solid and there are 3 Picatinny anti-movement locks. I like that the tension and torque specs are marked clearly on the mount and are easy for anyone to see. Helps mounting!However, there were some scratches and marks on the mount I received so I'm not so sure about Quality control here.
D
This thing is awesome and very good quality. The rings have alignment studs which is good for those with shaky hands. The quality is awesome for the price and I look forward to trying more from this company. Top notch for little money. Get these and you will be pleasantly surprised.
C
There is pretty much no such thing as a HIGH profile 34mm mount with THREE solid recoil lugs under SIX ounces. Yet, here we are. And it has indexing studs in the tube mounts. Yes, that is correct. The fasteners are all 1st rate, the finish is flawless. I have a set of their 30mm straight rings and it is the same gig: massive over-delivery. That is my review: I am very impressed by what they do.Doing this review led me to shop their scopes. If this is how they are doing things, count me in. A++ all day.
L
I purchased this for a 300 blackout, using a vortex scope. It will have better rigidity than two piece scope mounts. The somewhat skeletonized structure will aid in the lightweight goal of this build. The printed torquing pattern numbers are handy for assembly, but I think I will color them in to make them less obvious. It's not a top of the line $250 scope mount, but for the price point and for the range of under 300 yds, this mount will more than suffice.
